(2pcs/set) 3157 Anti Flicker CANBUS Resistors Decoder Avoid Fast Hyper Flash Turn Signal Blink Light Dashboard Error Code
AUXBEAM NEW CANBUS LED TURN SIGNALS
15% OFF NOW
- Shipping and Refund
-Standard socket/base type LED load resistors.
-50W 8 Ohm high power Lights error-free canceller capacitor decoder wire.
-Metal surface excellent for heat dissipation.
-Turn signal bulb or LED license plate lights to avoid hyper flashing.
-Used for turn signal light, daytime running light, etc.
See the product socket picture to help to make a confirmation.
Plug Type: 3157
(Our 3157 Models fits to most America-made car, if not fit your vehicle please contact us for order.)
▶Warning! Don't Touch By Hand Directly.
Load Resistors Heat Up Like Light Bulbs And Get HOT When Working.
Mount Them On Metal Surface, NOT Plastic.
Plug Type: 3157
Working Power: 50W 8 ohms
2* Decoder Adapter (One LED Load Resistor for One LED Bulb)
3047 3047R 3057 3057A 3057R 3156A 3157 3157a 3157R 3457 3457A 3757a 4057 4057R 4114 4157 4157NA 4157R 4257NA
Auxbeam Lighting is shipping worldwide covering North and South America, Europe, Asia, Africa, Oceania and more.
We employ the services of major, trusted international carriers to ensure your package arrives at your destination safely.
U.S. domestic orders are shipped from our USA warehouse for the fastest delivery times but exceptions may occur based on stock shortage - because of which we may have to ship from China.
International orders are shipped from our China warehouse.
U.S. domestic shipping: about 3-5 Working Days
International shipping: about 8-15 working days
A standard processing time of up to 48 hours is required before the order is shipped out.
Due to challenges posed by the pandemic, our carrier is temporarily experiencing shipping delays, which may delay your delivery. We are always work to get your package to you as quickly and safely as possible.
We offer free shipping on all of our products to customers in the Continental U.S. when orders over $19.99. Customers in other regions need to pay additional shipping costs(Specific amount please kindly refer to your checkout page).
Your tracking number will be sent in email immediately after we ship the order out. You may follow the link in the email to check the estimated arrival time of your order.
(Please note that tracking information will only be updated online in 1 working day after your order has been shipped.)
If the wrong information is provided (address, phone, email) and results in your shipment being undeliverable, the customer is responsible for the shipping cost for the 2nd shipment.
We do not offer overnight shipping.
If you have any questions, please feel free to contact us via email: Customer@auxbeam.com
This is a great bit of kit if you're retrofitting LEDs in place of filament bulbs. I'm no stranger to soldering, but it can be a bit of a hassle to make your own wiring harnesses. I'd know because I had to make my own harnesses for a tail light rebuild/retrofit. For the front end my project was going to be much simpler with only resistors for the turn signal bulbs, but I didn't fancy trying to solder these resistors inside my engine bay, nor taking the time to disassemble all those wiring harnesses at the front end to do a proper job on a workbench.Enter these fabulous (and very affordable) premade wiring harnesses. Easy as plugging it in and I was good to go! Quality is excellent, but I can't rate longevity at 5 stars because I've only had these a few weeks. Fitment of the bulb socket into your light housing will vary! I had to snip and shave some extra plastic off the locking tabs to make fitment, took all of five minutes with some nippers and a file.Superb, affordable, time-saving, ...
These resistors were easy to install and the instructions were very straightforward. They were used to stop the quick blinking on my F150 and the did the trick immediately. People said that they can get hot but I have not experienced that yet.
Used on 2002 Dodge Dakota factory tail lights,installed easily had to trim unused lock off one plug and file a little plastic off but still easier than it sounds. Fixed hyper flash. Find some 1/2 inch self tapping screws and do a solid mount on the resistors youll be glad you did
These kits are really great for making it easy and quick to get the led lights functioning without the hyperflash. They fit behind my light assembly nicely. I spent a few hours on a different vehicle wiring in the resistors, these saved me all that time. It is cheaper to wire the resistors in yourself, but if you consider time as money, you break even on these, and still have more time for other things.
Very good, thank you for this product